Articles Blog

How to fix iPhone 7 Cracked Camera Lens (iPhone 7 Plus too)

How to fix iPhone 7 Cracked Camera Lens (iPhone 7 Plus too)

Today I am going to show you how to replace
a cracked camera lens on an iPhone 7, and 7 Plus. The process is the same for both phone models,
and you don’t even have to open up your phone. Only attempt this project if your cracked
camera lens is keeping you from using your camera. Several things can go wrong during this repair,
which Ill explain as I go, and you really don’t want to risk anything unless you have
nothing left to lose. Now that we have that out of the way, lets
get started. [Intro] I am using a Bonafide Hardware glass camera
lens replacement for this project. Ill link these down in the video description. They are pretty inexpensive and you can find
them on Amazon. Bonafide Hardware sells two versions of this
lens. One with a frame, that is way harder to install,
and then this ‘Glass only’ version, which is what we are going to use today. It is incredibly small, but it is precision
cut for the iPhone 7. Now we start one of the hardest parts of this
project. Removing the old cracked glass. Heat is going to be your best friend during
this process. If you have hair, you can use your blow dryer. As for me, I am going to use a heat gun, Ill
warm up the lens until it is just barely too hot to touch with my finger. As you are pulling the glass chunks out from
the little circle make sure nothing falls into the camera itself. The camera, that you see underneath this broken
lens, is very fragile in more ways than one. First, it can scratch very very easily. Which means if any of the glass chunks brush
up against the actual camera, you’ll lose your focus ability. Also, there are moving parts inside the camera
that are a part of the Optical Image Stabilization, and these moving parts can get jammed up by
glass dust. So you want to keep the inside as free from
dust and glass bits as possible. I like to use a sturdy sharp razor blade to
remove the glass chunks, but you can also use a pair of metal tweezers. You’ll probably want to warm up the lens about
every 30 seconds or so, since it does cool down pretty fast. The adhesive gets tough when it cools down. You can hold the phone vertically to help
keep the glass and adhesive from falling inside; using gravity to your advantage. You do want to clean off that entire inner
ridge. Because if there are any dust or adhesive
‘pressure points’ left when you install the new lens, the new glass will be more prone
to breaking. You want that surface as flat as possible. Now we have that inner ledge pretty well cleaned
up. This looks big on your screen right now. But in real life it is incredibly small. This is like a repair project for ants. You can see how the camera moves around inside
the frame. This is part of the mechanical stabilization
I was talking about earlier. Thumbs up for apple finally implementing OIS. Also, at this point, the camera can still
take clear pictures and focus just fine even without a glass lens in place. Now to install this lens Ill need some clear
silicone. This can be purchased at literally any hardware
store, and it is dirt cheap. Ill include some in the video description
as well though. This clear sealant is made for aquariums,
sinks, tubs, and anything that might come in contact with water. So technically, your iPhone 7 will still keep
its water resistance with the new lens installed. But I still recommend avoiding water either
way. This adhesive is also rubbery, so it will
allow the lens to fluctuate with any temperature changes and not crack. I am going to take a wooden toothpick and
gently ‘dab’ some of the rubber sealant all around that inside shelf of the lens frame. Go slow. Don’t let any stray silicon strands drape
like a spider web over the camera unit. It’ll be a nightmare to clean up inside of
that hole. So go slow and be careful. This stuff doesn’t dry very fast, so you have
plenty of time to make sure the silicon is evenly spread around the edge. Now, the Bonafide Hardware lens replacement
for the iPhone 7 has two sides to it. One side is glossy, and the other side is
more of a matte finish. You want the glossy side facing outwards. The camera will still function if you get
the direction wrong, its just more aesthetically pleasing if you get the shiny side facing
out. Im going to remove the plastic cover over
the matte side, and then gently set the lens down into the hole we cleared and already
added silicon to, and Ill press it into place. Firmly, but gently, keep in mind that it is
still glass. As long as there is no glass dust or bits
of hard adhesive under the new lens it shouldn’t crack under pressure. The Bonafide Hardware glass is just as thick
as the original. If your lens did not come with the protective
plastic shields, just make sure it is clean on the underside before you install it. It takes about 45 minutes for the silicon
to get super tacky, and a full 24 hours to fully cure, or dry. So hold it in place with your finger for about
a minute or two before wiping off the exes silicon. Silicon is very easy to clean up when it is
wet. It just wipes away. Unlike super glue. Which would be a royal mess. Make sure the lens is flat inside its little
frame. And try not to disturb it for at least 2 hours,
or better, leave it alone over night. My focus ability is still intact after replacing
the lens, It would be difficult to tell that the lens was ever cracked in the first place. Its kinda fun that you can fix your iPhone
camera lens with some fish tank sealant, a tooth pick, and some replacement glass. Speaking of which, I have a spare lens just
to show that the Bonafide Lens is indeed real glass, and Here is both lenses side by side. on the left side is an original piece of Apple
iPhone glass, and on the right side is the Bonafide Hardware glass. Both are the same thickness, and pretty inexpensive. It might be smart to buy 2 lenses just in
case something goes wrong with the install. Hopefully this video was helpful! You can always find my behind the scenes stuff
posted on Twitter and Instagram. Lets see who’s still awake and made it to
the end of the video… Tell me what you had for breakfast in the
comments. I had a bowl of chocolate cheerios with a
scope of protein in it… Which actually now sounds kinda weird now
that I say it out loud. I do read all the comments! Even if I cant respond to every single one
of them. Thanks for watching! Ill see you around.

100 thoughts on “How to fix iPhone 7 Cracked Camera Lens (iPhone 7 Plus too)”

  1. you make it look so easy. if i attempt to fix it myself and i screw it up will that void my AppleCare+ warranty?

  2. I had crunchy cereal with protein powder and banana for breakfast💪🏻 loving your videos all the way from South Africa🍁🇿🇦

  3. The title is click bait. iPhone nines dont exist! (The title says 7 plus too) I know it's the wrong kind of 2

  4. Does the heating process to remove the glue work on locktite? I already replaced my lens using this guide, but there's some condensation trapped in there so I was considering doing it again. Can I heat it up to remove the super glue?

Leave a Reply

Your email address will not be published. Required fields are marked *